Home > Error Code > Cpo Error Code Hot Tub

Cpo Error Code Hot Tub

Contents

This could indicate poor flow or air bubbles in the heater. Make sure they aren't touching anything. HL = High limit switch tripped. Each time you change the water in the spa, you should check to be sure the locks on the slice valves are in good condition;... have a peek at this web-site

If not and you know flow is not the issue, most pressure switches have an adjusting collar that will vary the pressure it takes to activate it. The error codes above are related to a temperature sensor failure, overheat problems or a flow problem. Check to be sure no water is draining from the drain valve as you refill the spa. E97 Dry-fire Protection. http://www.spadepot.com/spa-error-codes.htm

Jacuzzi Hot Tub Error Codes

Thanks. Both are secured with black plastic nut around the gray cable. This code is used by the vendor to identify the error caused. There is a link to s Balboa site for service tech diagnostic help.

Compatibility: Windows 7, 8, Vista, XP Download Size: 6MB Requirements: 300 MHz Processor, 256 MB Ram, 22 MB HDD Limitations: This download is a free evaluation version. Support Intex Jan 30, 2015 | Intex Pool & Spa Pumps 1 Answer I have a J340 Spa that is throwing the watch dog mode --- error code. Std = Spa operating in Standard Mode. Marquis Spa Error Codes I do hvac and I used to work for a pool and spa company.

Well sorry about long post any any misspelled words. Balboa Hot Tub Error Codes Sn3 = Open or shorted sensor ( heater disabled). You can also check the pressure switch or flow switch with a an Ohm meter. https://www.poolandspacentre.co.uk/help/hot-tub-and-spa-error-codes.html I have a LP warning.

Misuse or abuse is defined as but not limited to: use of spa in non- residential situation, water temperatures outside the range of 32 to 110 degrees, damage... Great Lakes Hot Tub Error Codes It automatically activates all of the pumps and the blower to circulate water and warm the plumbing.Note: This auxiliary freeze protection functions at all times, even when another fault condition has Something like this really requires a technician to come out and take a look. With the system powered off, you normally unscrew the sensors from the heater manifold, and unplug the wire from the panel.

Balboa Hot Tub Error Codes

Kind Regards Karen admin June 27, 2012 at 9:57 am Hi Karen, I apologize my reply did not post before and I am not sure if you received my email. Not finding what you are looking for? Jacuzzi Hot Tub Error Codes Page 15 Electrical Information NFPA/70 and in compliance with Underwriters Laboratories, Inc.. How To Fix Flo Error Hot Tub Flow switches are plumbed in line with the plumbing.

The heater pump then wouldn't run but the jets worked fine. http://digitalezines.com/error-code/cscripts-exe-code.html Shut the spa power off, remove the filter and make sure all the jets are open. Power up and turn on low pump. SESH = Sensor short, nonfunctional. Vita Spa Error Codes

Disclaimer: This website is not affiliated with Wikipedia and should not be confused with the website of Wikipedia, which can be found at Wikipedia.org. If it does you know you need a new pressure switch. Inspect the wire and plugs, check the spa water level and make sure water is flowing free and fast. Source Vice President: An expert whose answer got voted for 100 times.

Please contact technical support at 877- 722-4097 for service or repair. Hydropool Hot Tub Error Codes Slice Valve... The spa runs perfect on both speeds and there is great jet action but the spa will not heat because of the FLO code.

Over return e past few years it just seems to shut off I can't seem to remember if it ever put out a code or what it was.

Spacare.com 888-772-9887 Technical Assistance 405-622-4950 0 Item(s) | Total: $0 Home Shop SpaCare.com Spa Part Index Circuit Board Repair Spa Covers Spa & Hot Tub Covers Spa Cover Lifts Note: The manual fix of Cpo Error Code Hot Tuberror is Only recommended for advanced computer users.Download the automatic repair toolinstead. Check the water temperature with an accurate temperature thermometer. Artesian Spa Error Codes Pump may also be deactivated).

It can also be caused if your computer is recovered from a virus or adware/spyware attack or by an improper shutdown of the computer. All the above actives may result in the deletion or corruption of the entries in the windows system files. If water temperature drops 20°F below set temperature, low speed pump and heater activates to bring temperature within 15° of set temperature. have a peek here The first thing you want to do before doing anything else is shut the spa down, remove the filter and make sure all the jets are open.

Snb = Spa is shut down. If you have a small circulation pump in your spa this could be clogged with debris and causing low flow. The steps laid out below is what I have all my customers do when they call me for a low flow error. You can check out this blog post here for more info on that: http://precisionpool.net/2010/10/how-to-release-an-air-lock-in-your-spa/ -Jay admin October 10, 2015 at 7:33 pm Hi Tim, Sounds like a bad relay or a